In order to login to helpdesk, please use your forum account.

RSS Feed
Knowledgebase

The antennas for this click can be found in the store under PID: MIKROE-2349 MIKROE-2350 For those antennas, you also need an adapter, IPEX to SMA: MIKROE-274
You can use following antennas for Lora click board depending on frequency. For 433MHz: MIKROE-2351 MIKROE-2352 For 868Mhz: MIKROE-2349 MIKROE-2350
This is normal behavior, cause if your Hexiwear's MCU is empty, the docking station with the Hexiwear on it would appear in maintenance mode. What you should do is this: Connect the Docking station to your PC with all switches on the Docking station tur...
Activation or Registration key that you get with Electronic License Delivery Option can be used on maximum two computers.
If this message appears make sure to reinstall the mikroProg Suite with administrator rights. You open the exe file with the right click on the icon, and by choosing the option "RUN AS ADMINISTRATOR". In the installation process choose the option "CUR...
If you are using Flip&Click (Arduino Duo) mikroBUS "B" chip select (CS pin) for SPI and you have problem, try to set it as: #define mikroBUS_B_CS 87 That pin assigment can be used for A29 or C26. For more information take a look at the Arduino IDE a...
Display parameters for 5 and 7 inch display with FT812 and FT813 display controller are: FT_DispWidth = 800; FT_DispHeight = 480; FT_DispHCycle = 1056; FT_DispHOffset = 46; FT_DispHSync0 = 0; FT_DispHSync1 = 10; FT_DispVCycle = 525; FT_Dis...
Deselecting the 'Restore Last Opened Project' will allow you to create new project without need to close other project on which you have worked before. That way the new created project will not affect the existing project on which you have worked prior ...
The Peripheral Pin Select library enables user to have more than one digital peripheral multiplexed on a single pin. Users may independently map the input and/or output of any one of many digital peripherals to any one of these I/O pins. The peripherals...
If you want to know what are your touch calibration constants you can make example which will read that for you. Then you can use that constants in the project to avoid manual calibration. 1. Make some calibration example with the blinking points (man...
If you are using I2C PPS on PIC note that you should set Output first then Input: PPS_Mapping(_RC4, _OUTPUT,_SDA); // Sets _RC4 to be Output, and maps SDA Output to it PPS_Mapping(_RC3, _OUTPUT,_SCK_SCL); // Sets _RC3 to be Output, and maps SCL Output ...
To install the library, use Package Manager, our free software. http://www.mikroe.com/package-manager/ [http://www.mikroe.com/package-manager/] Once the library is installed, open the compiler. It should be visible in the Library Manager in the compil...
You cannot use internal oscillator for ICD with PIC16 and PIC18 family because of internal pull-ups activated on ICD lines in that mode. Only on PIC24, dsPIC30, and dsPIC33 chips you can use ICD with internal oscillator.
Our hardware is tested and fully functional on Windows 10. Drivers for Windows 10 can be downloaded on our website. In order to prevent any issue while working on Win 10, make sure to: 1. INSTALL THE DRIVER AS ADMINISTRATOR. That means Right click on ...
For SDIO to work on this mikromedia you need to change and set this: 1. In a MLK file you need to replace the ROM declaration with this. You can acces the MLK file for STM32F746ZG while in your project by pressing shortcut CTRL+ALT+M.
Bootloader is written for 120MHz, so any program written via the bootloader to MCU must use this frequency value in order to work correctly. You should use external programmer if you want to achieve any other frequency. Connections should be as followi...
Pointers with PIC16 are "near": they carry only the lower 8 bits of the address. Compiler will automatically clear the 9th bit upon startup, so that pointers will refer to banks 0 and 1. To access the objects in banks 2 or 3 via pointer, user should manua...
For working with the mikroProg for Kinetis you should folow manual: http://docs.mikroe.com/MikroProg_for_Kinetis [http://docs.mikroe.com/MikroProg_for_Kinetis] And install: - mikroProg Sute for ARM http://www.mikroe.com/downloads/get/2589/mikropro...
1. All function prototypes and function pointers have to be built using the same optimizer, because of different calling conventions in different optimizers. In SSA, function parameters are passed via working registers, and without SSA they end up in func...
If you need to toggle a pin on STM32 micro controller the fastest way possible you can try this code. void main() { unsigned long *ptr; unsigned long val = 2; unsigned long val1 = 2ul << 16; GPIO_Config(&GPIOB_BASE, _GPIO_PINMASK_1, _GPIO_CFG_DIGIT...
If you notice that your STM32F1 or STM32F4 work bettwer with the TFT then STM32F7 then you should do next. Go to the compiler folder: ...MikroelektronikamikroC PRO for ARMDefs Open .mlk file of the STM32F7 MCU which you want to use and replace your ...
The problem is related with Windows 7. Try installing Visual C++ redistributable package 2010 suitable for your windows. https://www.microsoft.com/en-us/download/details.aspx?id=5555
Codes that work for Wifi ESP will work for Wifi 3 click. This is tested with the default example written for HEXIWEAR named WiFi_ESP. After finishing testing with Wifi ESP click this is tested with Wifi 3 click and worked with both of thees click boar...
Most Popular 
 
Recent Articles